Scale for Office Tower Model: Keeping Floors and Podiums Readable

November 17, 2026 · by Moriasi Architectural Model Makers

A twenty storey tower shrunk too far becomes a smooth stick that shows a client nothing, while one scaled too large will not fit through the boardroom door. The right ratio keeps floors, facade and podium readable at the size your table allows. Settle it before you order.

Plan your tower model with Moriasi3D

See everything Moriasi3D Models can do for you.

Scale for Office Tower Model: Keeping Floors and Podiums Readable

Choosing the right scale for office tower model work is one of the first decisions a developer or architect has to make, and it is easy to get wrong. A tall building asks a model to do two jobs at once: show a slender vertical mass and still reveal the floors, facade and base that make the design worth studying. If the ratio is too small, a twenty storey block turns into a smooth stick that tells a viewer almost nothing. If it is too large, the model may not fit through a door, let alone onto a boardroom table. Good scale model designs find the balance by testing real dimensions from your drawings before any material is cut. At Moriasi3D Models in Nairobi, we have built many towers for clients across East Africa, and the same questions come up each time. This post walks through those questions so you can decide on a ratio with confidence before you order.

Why tall buildings are harder to model than they look

A tower looks simple on a drawing, but its height creates a problem that low buildings never face. Twenty storeys at roughly four metres each reach about eighty metres, and that whole height gets squeezed into a band that a viewer takes in at once. At a small scale, each floor becomes a sliver only a few millimetres thick. The eye reads the tower as a single block, and the rhythm of floors that the architect designed disappears. This is the first reason towers need more thought than a villa or a shop.

The base of the building brings a second challenge. Most office towers sit on a podium that holds retail, parking, a lobby or a terrace, and these levels have their own character. They are wider than the tower, closer to the street, and full of detail such as canopies, entrances and stepped roofs. On a model, the tower rises above them and tends to dominate attention, so the podium can look like a plain plinth. Showing both parts well means the scale must leave enough room for the lower levels to breathe.

Clients usually care most about two zones, the ground plane and the skyline. The ground plane shows how people arrive, how the building meets the street and how it relates to its neighbours. The skyline shows the proportions, the crown and how the tower will look from a distance. A scale that favours one and ruins the other leaves the model half useful. The right choice protects both, which is why we ask about these priorities before suggesting a ratio.

How the scale for office tower model changes with height

For a typical ten to twenty storey block, three ratios come up most often: 1:200, 1:100 and 1:50. At 1:200, a four metre floor measures 20 millimetres, and a twenty storey tower stands around 400 millimetres tall. At 1:100, the same floor is 40 millimetres and the tower reaches about 800 millimetres. At 1:50, each floor is 80 millimetres and the tower rises to roughly 1.6 metres. Those numbers show quickly why the ratio matters so much for how the model reads.

Two dimensions set the practical limit, the footprint and the total height. A tower with a 40 metre square floor plate measures 200 millimetres across at 1:200, 400 millimetres at 1:100 and 800 millimetres at 1:50. Add the podium and the surrounding plot, and the base board grows much faster than the tower itself. A tall slim tower may therefore suit 1:100 comfortably, while a wide and heavy one pushes you toward 1:200. We look at both measurements together rather than judging by height alone.

A larger ratio gives more floor detail, but it also demands a bigger table, more material and a longer build. Moving from 1:200 to 1:100 doubles every linear dimension, so the base area grows fourfold. That affects cost, transport and where the model can sit afterwards. For many office projects, 1:200 is the workable choice for a full site model, while 1:100 is better when the tower is the sole subject. A 1:50 tower is usually reserved for a section or a single bay rather than the whole building.

Keeping floors, facades and podiums readable

Floor-to-floor lines are the heartbeat of a tower model, and they need to stay visible at normal viewing distance. A viewer standing a metre from the table should be able to count floors without leaning in. At 1:200, a 20 millimetre floor band can read well if the slab edges are crisp and the glazing sits slightly recessed. Below that size, shadow lines get too thin to notice. We treat the slab edge as a deliberate feature, not an afterthought, because it carries the whole vertical rhythm.

Facade articulation needs a minimum size before it reads as design rather than noise. A 1.5 metre glazing grid becomes about 7.5 millimetres at 1:200, which is just enough to show a pattern, while at 1:100 it is 15 millimetres and feels crisp. Balconies, fins and sunshades are harder, because a 150 millimetre fin would be under one millimetre at 1:200. In those cases we exaggerate the element a little or suggest the pattern with etched lines. The goal is to keep the character of the facade rather than copy every part literally.

Podium levels can take a slightly different treatment so that the tower does not swallow them. We might use a warmer material for the podium, add more visible detail at the entrances, or lift the tower on a clean, lighter volume. Terraces, planting and canopies can be shown more clearly because they sit near eye level. This keeps the street edge lively without changing the overall scale. The viewer then reads two distinct parts, a human scaled base and a tall, quiet shaft above.

Practical decisions to make before ordering

Start by deciding which audience the model serves, because planners, investors and design reviewers look for different things. Planners tend to want context, setbacks and heights relative to neighbours, which favours a smaller ratio with a wider site. Investors usually want a clear, attractive view of the whole building, where the crown and the entrance matter most. Design reviewers need facade and floor detail, and they may prefer a larger ratio for a single tower. Naming the main audience early lets us pick a scale that answers their questions first.

Next, confirm where the model will live and how it will travel. A model that must be carried to meetings in other towns needs to be lighter and more compact than one that stays in a sales office. A boardroom table might allow only a 900 millimetre board, while a showroom could host a much larger display. Doors, lifts and vehicle boots all set real limits that are easy to forget until delivery day. Telling us these details up front can change the scale recommendation more than any design factor.

Finally, share your drawings with the model maker as early as possible so the scale is tested against real floor plans. Plans, sections and elevations show where the floor heights, setbacks and podium steps fall at each ratio. We can flag problems such as a fin that vanishes or a terrace that is too small to model cleanly. Early sharing also lets us suggest simple changes, such as simplifying a repeated detail, that save time later. A short conversation at this stage usually costs far less than rework after the build has started.

Working on office towers across East Africa

Nairobi office towers often sit on dense plots, so the model must show setbacks and neighbouring buildings clearly. A tower that looks slender on its own can feel very different once adjacent blocks, access roads and service lanes are included. Reviewers want to see how the podium meets the boundary and how light reaches the street. That often pushes us toward 1:200 for the full context, with the tower itself built carefully so floors still read. Getting the surroundings right is as important as the tower, because the plot is where most planning questions are asked.

Our team has built many completed models in the region and can advise on what has read well for local reviewers. We know how approval meetings, investor presentations and sales offices tend to run in Nairobi and across East Africa. That experience helps us suggest materials, colour treatment and lighting that stay clear in real rooms. One practical step is a short scale test on a single floor, built at the proposed ratio and checked against your drawings. It takes little time, and it often saves rework and cost later, because everyone can see the result before the whole tower is committed.

Choosing the scale for an office tower model comes down to matching the ratio to your audience, your plot and your table. Smaller ratios such as 1:200 keep the full site and skyline in view, while 1:100 gives the tower itself more presence and detail. Floors, facades and podiums stay readable when the slab edges, glazing rhythm and base treatment are designed for the chosen size. Thinking early about transport, display space and who will study the model prevents most of the problems we see. Sharing your drawings with us before you order lets us test the scale against real floor plans rather than guess. If you are planning a tower in Nairobi or elsewhere in East Africa, our workshop on Mucai Road, off Ngong' Road, is ready to help you make that decision with confidence.

See everything Moriasi3D Models can do for you.

Visit Moriasi3D Models →